Read piano silicone mold soap plaster wax resin clay 5oz music notes reviews, rating & opinions:
Check all piano silicone mold soap plaster wax resin clay 5oz music notes reviews below or publish your opinion.100 Reviews Found
Sort by: Most Accurate (default) | Newest | Top Rated
These molds worked amazing with fondant. The impression was very nice and uniform with every use. Excellent for what I needed.
This is great! I adore the rose design, it came out really well. The only issue I had was getting the candle out once it had cooled, but I discovered that if you chop the mold about halfway down the side the candle pops out with small difficulty. Despite being so small, all in all this was a beautiful amazing product
THIS WAS A COMPLETE WASTE OF DOESNOT LOOK LIKE THIS AT E MOLD IS SO SMALL THAT YOU CAN BARELY SEE THE CANDLE..I HATE IT AND WOULDN'T RECOMMEND ANY ONE.
Bought this to create party favors for a wedding. The candles came out ok. I had to chop down one side of the mold to obtain a candle out without the petals falling off. Once i got the hang of it most of the candles came out beautiful good.
Horrible, Horrible Horrible. I want I could rate this a zero but I can’t. I bought this mold and thought it would be ok first of all it was little and then when I tried to use it anyway I allow my candle settle overnight it was completely dry and ready to be chop out of the mold but when I chop the mold the rose crumbled like cookie crumbs I am beyond upset about this I thought this was a amazing product turns out it’s crap
It's really small, but it's cute. Getting the candle out of the mold is not an simple task either. I had to chop a small slit in the mold to obtain it out without it breaking and chipping.
It's quite hard to obtain the candle out of the mold. I broke some of the design away trying to obtain it out. But it's very beautiful and I'm going to hold trying various ways.
The mold itself is beautiful cool &easy to use. The reason I didn't give more stars is because the hint of the gun is so thin that it will bend& break very very easy. I had to chop out more zone for the resin to fill it in better
I do not like the zone of the hole intended for hanging the finished product. In my opinion the hole zone in the soldiers head is disrespectful. However I have modified my use of the mold to remedy that oversight.
I love how super soft the molds are so popping out the wax is easy. I have a various dog mold that I had to chop the mold on either side because the silicone mold was too hard to obtain the wax out. these are super simple to use and very adorable too.
My wife has a lot of of these molds and lets her artistic meal creativity run free. People at her work are buying what she makes with these and share them of social media.
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
I used this mold to create almond pudding winter tree for my YouTube channel. It's a bit hard to unmold since the material is very thick. I had to freeze it before unmolding. Amazing thing it turned out nicely!
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
I used this mold to create almond pudding winter tree for my YouTube channel. It's a bit hard to unmold since the material is very thick. I had to freeze it before unmolding. Amazing thing it turned out nicely!
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
I used this mold to create almond pudding winter tree for my YouTube channel. It's a bit hard to unmold since the material is very thick. I had to freeze it before unmolding. Amazing thing it turned out nicely!
Being created from very thick silicone, it's simple to remove the candle. Simply roll it off. Don't have to worry about tearing due to the thick silicone. For candle making, you'll need to punch a little hole at the "tree top". Push the wick thru it and anchor the wick like you normally would with a toothpick, pencil...etc. Don't worry about wax leaking. The silicone self seals. Besides, the tree top is the bottom, so the wax will seal the mold.
Wow, this turns out great! As a beginner candle maker, I was a small worried that it would be hard to use, but don’t worry! It’s a cinch. Here are some hints for beginners.(Pre-step - melt your beeswax in a double boiler (or a jar inside a pot of water) and add mica powder for color. Add your essential oils after the wax is melted.)1. Create a hole - First, with a needle or a sharp pencil, poke a little hole through the hint of the mold (the top of the tree).2. Getting the wick through - Then, wrap the wick around the hint of a paper clip. To obtain it to stick to the paper clip, I dip the wick in hot wax and [email protected]#$%! on there. Then, I carefully push the wick through the hole. Don’t worry, even though there’s a hole now, wax won’t leak through because the silicone makes a amazing seal.3. Centering the wick - I use another paper clip to keep the wick in the center. See my pictures for reference.4. Pour your hot melted wax into the silicone mold. Use beeswax, which is harder than soy wax. Another review said soy wax is too soft to create this kind of candle.5. Wait a few minutes. When the wax cools, it compresses and it will sink in. Pour some more wax on top.6. Decanting your candle - Create sure it’s solid! You can place it in the freezer to speed up the solidification process. When it’s hard, roll back the silicone. This part is a small tricky. But the mold is amazing quality and hasn’t torn for me. Roll it until it’s almost inside-out and then pop! Out comes your candle.
Amazing mold if you know how to use it, very detailed, I simply loved it! I'm sure to obtain years of use from this product.
Created 30 candles. Was a bit smaller than I expected but just means everyone got 2. I suggest you obtain more than one mold because it takes some time to create many. Or you can be stubborn like me and only obtain one mold. It can take it, woot
Useful review?
Nice soap model
0
Useful review?
Perfect soap mold. Arrived early. Simple to use, durable and detailed. WORTH the cost.
0
Useful review?
[email protected]#$%! was deeper
0
Add your opinion on piano silicone mold soap plaster wax resin clay 5oz music notes or scroll down to read more reviews ↓